2.5 Inch GAS HIGH CLEARANCE LONG ARM JEEP WRANGLER JL SUSPENSION SYSTEM with Plush Ride Springs FOR JLU ( 4 DOOR ONLY )

EVO MFG
EVO-3015
$3,886.49
$3,886.49

The EVO MFG 3.5 Inch JLU High Clearance Long Arm kit will lift your JLU 2.5 Inches. Through specifically designed bracketry we accomplish the ultimate in suspension and chassis clearance, larger wheel travel ability, optimal suspension geometry with increased ride quality. Clearance, ride quality, performance and ease of installation was our focus in creating this long arm suspension system. The front arms mount tucked up inside nearly flush with the bottom of the frame mounting inches above the stock front lower mounting bracket. The rear mounting locations for the long arm are on the side of the frame, above the bottom giving inches of clearance over the factory locations as well. Keeping optimal geometry while maintaining as much clearance was critical in the design of this system. In doing so, not only did we raise the rear control above the frame but we raised its mounting at the rear axle by multiple inches as well. This allows for an incredible ground clearance increase but just as importantly retaining flat and optimal control arm angles giving ideal ground clearance, smooth ride quality and long travel ability. The mounting brackets are specifically designed to require no exhaust cutting on 3.6L Jeep Wrangler JLU’s (minor grind/clearance to flange required) and have full length hard-face mounting surfaces that weld to your frame giving redundant and ample welding area and strength to their mounting. The mounting brackets align to the frame simply using existing factory holes giving complete assurance of proper locating during install. Simply bolt brackets up to frame with existing hardware and weld them in place. These kits come with a set of 3.5” Plush Ride Lift springs specific to each corner which will keep the Jeep Wrangler JLU more level side to side and will maintain a unique and compliant ride quality. EVO MFG Long Arm joints feature Johnny Joints on both ends of the control arms for restriction free articulation and motion with no wearable and limited bond rubber. All EVO MFG lower long arms are built with strength in mind. These arms are made from industry leading 2.0” x .281” wall Steel DOM Tubing. Include in these kits is front brakeline extension brackets, Rear swaybar endlinks and front and bumpstop extensions. Cutting, grinding and welding of frame brackets required. The EVO MFG 3.5” High Clearance Long Arm kits require no driveshaft or exhaust modifications (your shock choice may require this, contact manufacturer to be sure). Option of retaining factory shocks, maintaining wheel travel with use of shock extensions (part number EXT kits) or without shock extensions to allow for use of your choice of aftermarket 2/5” lift shocks. EVO3015K kits come with EVO SPEC King 2.5” Remote Reservoir shocks all 4 corners. 2.5” lift is based on increase of our 4 Door Rubicon. 4 Door Sport and Sahara Models will see slightly higher increases over stock and will match overall lift height of a Rubicon Model.


Note: Depending on actual tire variances and sizes, Some minor factory inner liner plastic may need to trimmed/removed to fully clear some tires under compression. These kits require wheel spacers or aftermarket wheels with smaller backspacing.

When paired with packaged shocks, these kits will not require driveshaft replacement.

Adjustable Front Trackbar is required to complete proper installation, Front and rear adjustable trackbars are included with PLUS “P” kits

NOTE:

Compatible on 4dr. JL Unlimited Only

INSTALLATION TIME 20-28 HOURS

Image may differ from actual product

WARNING: This product can expose you to chemicals including silica, crystalline which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.

Read More
Read Less

INSTALLATION INSTRUCTIONS

EVO3015_3016.pdf

All Products Manufactured by EVO Manufacturing shall have a Limited Lifetime Warranty on defects in material and craftsmanship.

All products must be on the original vehicle it was installed on by the original purchaser and is not transferable

Proof of purchase is required for all warranty claims

EVO Manufacturing is not responsible for any labor charges, shipping charges and other costs in result of a warranty claim of any EVO Manufacturing product

EVO Manufacturing is not responsible for any and all costs associated with incidental and consequential damages and are excluded under this warranty, regardless of when, where or why the warranty occurs

All EVO Manufacturing products must be deemed to be installed correctly, unaltered, free from abuse and combined with other appropriate equipment/products/components.

All return/warranty products must be recieved in new, unused, unmodified, undamaged condition to qualify for credit. 

Exceptions to stated warranty:

Wearable items are not included in warranty.  These products include but are not limited to tie rod ends, draglinks, bushings, bump stops, bearings, heim joints, uniballs/spherical bearings etc. and hardware

Any substitution of other manufactures components or exemption of required and or supplied components will immediately void all warranties.

EVO Manufacturing does not warranty any product not manufactured by EVO Manufacturing.

EVO Manufacturing warranty applies to only products purchased, sold, installed and remaining in the United States of America.

All product finishes provided are warranted to be free from defects at time of sale only.

Springs and Shocks are warrantied against manufacturing defects only and are only returnable if they have not been installed on a vehicle.

EVO Manufacturing products that are used for competition and or racing immediately void all warranties.

EVO Manufacturing recommends the installation of EVO MFG products be installed by certified technicians only.

EVO Manufacturing is not responsible or liable for any loss, damage, injury whether consequential, ordinary, direct, special or incidental arising from the manufacture, sale, resale, installation, delivery, possession, handling and or use of its products.

Electronic components and products provided by EVO MFG will have a 90 Day Warranty and must be deemed free if any tampering or accidental damages or abuse.

EVO Manufacturing is not responsible for any typographical errors in either pricing or content related to all EVO Manufacturing related products, items, websites, packaging, instructions etc.

 

Disclaimers:

Warranties: EVO Mfg. disclaims any other warranties, whether express or implied, beyond those set out in the above-entitled “Warranties” provision. Warranties specifically disclaimed include but are not limited to any implied warranties, any warranty of suitability, any warranty of merchantability, or any warranty of fitness for a particular purpose.

Consequential Damages: EVO Mfg. will not be responsible for damages resulting in negligence, alteration, accident or use for which the part was not approved by the manufacturer or EVO. EVO will not be responsible for loss time, inconvenience, loss of use of a vehicle or any other consequential damages, or labor for removal from the vehicle and reinstallation (if any) or any part or merchandise.

 

Shipping:

We ship our parts anywhere in the world.  Due to varying shipping rates, taxes and duties we require all orders to be placed through email (sales@evomfg.com) or phone calls (310.761.9588) to better assist you, the customer, in receiving the most accurate and cheapest shipping rates.  

Please allow one business day for order processing. The majority of orders are shipped immediately if your item is in stock and available. You will receive an email notification within 2 business days, notifying you that your item(s) has shipped. If your item is currently not in stock, it will have to be made to order which may take up to 8 weeks. In such instances you will be contacted via email by Customer Service. 

Terms of sale: All products shipped FOB EVO MFG and the buyer assumes all risk of damage or loss.
Insurance is available through the carrier at an additional charge. Signature required is available upon request.

Please note because we are located in Southern California all orders shipping to locations within Southern California usually arrive the next business day via Fedex or UPS Ground.

For orders shipping outside the US, please email sales@evomfg.com for shipping options.

Damaged or Missing Items:  


Please verify that all contents shown on the bill of materials located on the instructions are free from damage or defects.

EVO MFG will not be held resposible for missing or damaged items caused by shipping or packaging.

EVO MFG must be notified if you have missing or damaged items within 7 days after delivery date. Contact 310.761.9588

FITMENT VERIFICATION:

All raw products should be checked for defects and for proper fitment prioir to powdercoating or painting. Incorrect items or defects must be brought to the attention of EVO MFG prior to powdercoating or painting.

EVO MFG is not responsible for cost associated with powdercoating or painting of parts that were not previously verified.  

Sales Tax
For all orders shipped within California, there will be an 8.00% sales tax automatically calculated and added to your order total at time of checkout. Orders shipping to all other states will be exempt from sales tax.

Cancelling or Changing Orders
Orders can not be cancelled once you have completed the checkout process. However, we will do our best to accommodate you if you need to make any changes. Please contact Customer Service as soon as possible.

Your cart

×