JLU (4-Door) GAS 3-5" LIFT KING 2.5" COILOVER PRO SUSPENSION SYSTEMS JEEP WRANGLER

EVO MFG
EVO-241B-3P
$7,569.00
$7,569.00

JEEP WRANGLER JLU (GAS) ADJUSTABLE 3-5" KING 2.5" COILOVER PRO SUSPENSION SYSTEMS (4-Door)

JL Enforcer PRO Stage 1 kits include the necessary upgrade suspension parts to convert your JL suspension to front and rear coilovers.

JL Enforcer PRO Stage 2 kits include Stage 1 components as well as EVO MFG Enforcer JL Front Lower Adjustable Control Arms to allow for caster adjustments. Stage 2 is the recommended minimum kit for all currently unmodified/stock suspension JLUs.

JL Enforcer PRO Stage 3 Kits include stage 2 components as well as EVO MFG Enforcer rear upper adjustable control arms for rear pinion angle adjustment. Stage 3 is the recommended minimum kit for JLs with aftermarket rear driveshafts.

JL Enforcer PRO Stage 4 kits include stages 1 components with addition of all 8 EVO MFG Enforcer control arms for full front and rear axle adjustments. The Ultimate Coilover Short/Mid Arm Suspension System.The coilover component of these kits is where the rear performance resides.

With the release of the JL Wrangler and EVO Manufacturing’s history in providing the most proven high-performance Jeep Wrangler Coilover suspension systems, we knew this high-performance product must continue on the JL.
Our primary focus from the moment we started this coilover conversion project was to build the most high-performance largest wheel travel, lowest lift (LCG) product possible.
The JL suspension and inner wheel wells gave us an excellent canvas to do so. Starting in the front with wide openings, high engine accessorial mounts and outboard shocks we found the ideal location.
By placing the shock upper mount up and rearward of its factory location, we are able to tuck the shock in close to the frame keeping it further away from tire which allows for more tire clearance and less backspacing requirements, but also allowing for a longer shock, more actual wheel travel and even lower minimum lift heights.
We then involved King Shock Technology and their engineers to build a custom length 2.5” Diameter long travel remote reservoir coilover to maximize travel and lift height. The high tucked in bracketry and custom long travel coilover produces the ultimate bolt on front coilover kit available.
With the same philosophy in mind as the front, we set out to build the most high performance rear coilover kit for the JL. We took the outboard mounting to whole new level but reinforcing both upper and lower mounts keeping the shocks slight reward mounting, optimizing travel without sacrificing the motion ratio.
We, with the aid of King Shock Technologies built a custom length specifically valved and tuned 2.5” Diameter long travel remote reservoir coilover to maximize travel and lift height.

Enforcer PRO:
The JL Enforcer PRO Kits achieve control arm limited 11.5/12” of wheel travel with only 3-5” (lift height is adjustable) of lift and most wheel and tire combination will require a backspacing of 3.75” or smaller.
Necessary equipment is included to convert including brake line provisions, bump stop extensions, swaybar end links, limit straps and hardware.
All Bracketry is laser cut, CNC press brake formed and fixtured welded for great fitment. This product is easy to install by the mechanically inclined or professionals.
Bolt on installation (Some cutting and drilling required). PLUS kits include Front and Rear adjustable trackbars. Factory front driveshaft is compatible, aftermarket optional.

High Clearance Long Arm PRO: Unlimited 14.5" of wheel travel with only 3-5” (lift height is adjustable) of lift and most wheel and tire combination will require a backspacing of 3.75” or smaller. Bolt on and Weld on installation (Some cutting and drilling required). PLUS kits include Front and Rear adjustable trackbars.   Front Aftermarket Driveshaft required to achieve the Long Arm compatible 14.5" of wheel travel (non limit strapped).  EVO High Clearance Long Arm is only compatible on 4 Door JLU

https://evomfg.com/products/front-vented-aluminum-inner-fenders-for-jl-jt

Read More
Read Less

All Products Manufactured by EVO Manufacturing shall have a Limited Lifetime Warranty on defects in material and craftsmanship.

All products must be on the original vehicle it was installed on by the original purchaser and is not transferable

Proof of purchase is required for all warranty claims

EVO Manufacturing is not responsible for any labor charges, shipping charges and other costs in result of a warranty claim of any EVO Manufacturing product

EVO Manufacturing is not responsible for any and all costs associated with incidental and consequential damages and are excluded under this warranty, regardless of when, where or why the warranty occurs

All EVO Manufacturing products must be deemed to be installed correctly, unaltered, free from abuse and combined with other appropriate equipment/products/components.

All return/warranty products must be recieved in new, unused, unmodified, undamaged condition to qualify for credit. 

Exceptions to stated warranty:

Wearable items are not included in warranty.  These products include but are not limited to tie rod ends, draglinks, bushings, bump stops, bearings, heim joints, uniballs/spherical bearings etc. and hardware

Any substitution of other manufactures components or exemption of required and or supplied components will immediately void all warranties.

EVO Manufacturing does not warranty any product not manufactured by EVO Manufacturing.

EVO Manufacturing warranty applies to only products purchased, sold, installed and remaining in the United States of America.

All product finishes provided are warranted to be free from defects at time of sale only.

Springs and Shocks are warrantied against manufacturing defects only and are only returnable if they have not been installed on a vehicle.

EVO Manufacturing products that are used for competition and or racing immediately void all warranties.

EVO Manufacturing recommends the installation of EVO MFG products be installed by certified technicians only.

EVO Manufacturing is not responsible or liable for any loss, damage, injury whether consequential, ordinary, direct, special or incidental arising from the manufacture, sale, resale, installation, delivery, possession, handling and or use of its products.

Electronic components and products provided by EVO MFG will have a 90 Day Warranty and must be deemed free if any tampering or accidental damages or abuse.

EVO Manufacturing is not responsible for any typographical errors in either pricing or content related to all EVO Manufacturing related products, items, websites, packaging, instructions etc.

 

Disclaimers:

Warranties: EVO Mfg. disclaims any other warranties, whether express or implied, beyond those set out in the above-entitled “Warranties” provision. Warranties specifically disclaimed include but are not limited to any implied warranties, any warranty of suitability, any warranty of merchantability, or any warranty of fitness for a particular purpose.

Consequential Damages: EVO Mfg. will not be responsible for damages resulting in negligence, alteration, accident or use for which the part was not approved by the manufacturer or EVO. EVO will not be responsible for loss time, inconvenience, loss of use of a vehicle or any other consequential damages, or labor for removal from the vehicle and reinstallation (if any) or any part or merchandise.

 

Shipping:

We ship our parts anywhere in the world.  Due to varying shipping rates, taxes and duties we require all orders to be placed through email (sales@evomfg.com) or phone calls (310.761.9588) to better assist you, the customer, in receiving the most accurate and cheapest shipping rates.  

Please allow one business day for order processing. The majority of orders are shipped immediately if your item is in stock and available. You will receive an email notification within 2 business days, notifying you that your item(s) has shipped. If your item is currently not in stock, it will have to be made to order which may take up to 8 weeks. In such instances you will be contacted via email by Customer Service. 

Terms of sale: All products shipped FOB EVO MFG and the buyer assumes all risk of damage or loss.
Insurance is available through the carrier at an additional charge. Signature required is available upon request.

Please note because we are located in Southern California all orders shipping to locations within Southern California usually arrive the next business day via Fedex or UPS Ground.

For orders shipping outside the US, please email sales@evomfg.com for shipping options.

Damaged or Missing Items:  


Please verify that all contents shown on the bill of materials located on the instructions are free from damage or defects.

EVO MFG will not be held resposible for missing or damaged items caused by shipping or packaging.

EVO MFG must be notified if you have missing or damaged items within 7 days after delivery date. Contact 310.761.9588

FITMENT VERIFICATION:

All raw products should be checked for defects and for proper fitment prioir to powdercoating or painting. Incorrect items or defects must be brought to the attention of EVO MFG prior to powdercoating or painting.

EVO MFG is not responsible for cost associated with powdercoating or painting of parts that were not previously verified.  

Sales Tax
For all orders shipped within California, there will be an 8.00% sales tax automatically calculated and added to your order total at time of checkout. Orders shipping to all other states will be exempt from sales tax.

Cancelling or Changing Orders
Orders can not be cancelled once you have completed the checkout process. However, we will do our best to accommodate you if you need to make any changes. Please contact Customer Service as soon as possible.

Your cart

×